Description

Vertical & Overhead Broadcast Applications

There is no better process to broadcast or scatter into wet resins on a vertical or

overhead application than the BroadcastPro6.

 

Whether it's a 6" cove base, a 1' fork lift bumper curb, or a 6' wainscoting, even a full wall or ceiling coating, gas curbs or a set of steps in a residential setting, the BroadcastPro6 is terrific for broadcasting flake, colored quartz, silica sand, natural aggregates, etc., professionally, economically, quickly and easily,

 

IN ONE PASS.

 

Read & Watch the Testimonials Below from Gary an Applicator in the Midwest.

 

"The blower work well on the jail project. We installed quartz on the wall and without the blower this could not have happen. Thanks for all your help and I would expect to purchase another one in the 2nd qt. of 2010."  

Here's an email from Greg, an applicator on the East Coast

"using your machine on a few thousand ln. ft. of cove in this maze of a project. Incredible what we got done with it last night."
A video Greg shared with us (below) about the project.
 

Realizing the Full Potential of 'The Machine' in Regards to

 Vertical Broadcast Work

 

 Watch this novice blower crew above realize the full potential of 'the machine' and blow/broadcast a wall and the floor coating with CQ sand;

All At The Same Time

(more short videos below)

 In the old days, contractors were taught by other old timers that vertical work had to be done first when applying broadcast floors, as I was.  The main reason for this, broadcasting methods were done by hand and usually it required two flake or quartz broadcasts to 'cover'.

Most applicators would shy away from vertical work and didn't even offer it to their customers.  And a wainscot or full height wall broadcast, completely out of the question.

Applicators caught up in a situation where a wall coating was required or specified, they would 'jack up' the price to the moon for the wall coating, list the wall coating portion as an 'Alternate' on their Proposal, hoping the owner would NOT take the option.  I know because I did it and so did a lot of other contractors I knew. This is still the case in some spheres of flooring contractors. 

IT DOESN'T HAVE TO BE THIS WAY!!!

Broadcast Cove Base or Gas Curbs Right Along With The Floor  

OH YES, YOU HEARD IT RIGHT!!!

The notion that coves or other verticals must be done separately (in most cases) is a myth propagated by the old guys from the past simply because they didn't have the machinery to do it any other way.  This 'myth' has been passed down through the years and to some, it's 'gospel', which it isn't.

 

Early on we were out to rewrite the book on archaic procedure and application techniques observed in this industry in the mid 70's through the 80's. Having re-wrote the book on many, these techniques will save you money during the application process of a broadcast or scatter floor, wall, deck, bridge, or roof broadcast project.

 

I am going to show you a few videos, (SOME OVER 25 YEARS OLD) that completely dispel these myths/insanity that have floated around this industry for decades. 

A Little History

Hand (double and sometime triple) broadcasting verticals and doing it separately from the floor is a very time consuming, expensive procedure.  There are ways to circumvent it with the right method and means.

Application modernization took hold on a parochial level here in the US during the early to mid 80's. Experimentation with means and methods lasted for ~5 years before suitable systems were developed.  The efficacy was tested and confirmed in the field for a few more years.  Experimentation took place to circumvent the problems associated with hand broadcasting.  A suitable procedure to mechanize a lot of the mundane, time consuming, and expensive chores associated with broadcast floors, especially the vertical, was well established and used by a few applicators in the mid to late 80's.  By the 90's, it was widespread in the Midwest Region of the USA and savvy applicators were using our broadcast machines on a consistent basis.

 

 

WITH THE BROADCASTPRO6, GONE ARE THE DAYS OF COATING AND BROADCASTING VERTICALS IN TWO SEPARATE, TIME CONSUMING,

EXPENSIVE OPERATIONS. 

Never Shy Away From Vertical Work. Promote the Hell Out of  It, And Here's the Reason Why! 

With the BroadcastPro6 doing any kind of vertical work is very easy.  Usually the prep is minimal, the application can be thinner that the floor in some cases, and you can charge more per square foot or meter than the floor. Your profit margins are very high on vertical work because it's perceived to be more difficult.  In reality it's easier with the broadcast machine.  Most of your competition doesn't chase this type of work so you can grab more money and profits out of a job, than the next guy, in addition, It separates you from the 'pack' which usually transforms into more work coming your way. 

Want to know the 'tricks of the trade'?

Simply call or email and we would be glad to share the information with you.

Watch these videos below, some from the late 80's and early 90's!

COVE BASE AND BUMPER CURB VIDEO BROADCASTING ALONG WITH THE FLOOR 

WALL AND WAINSCOT BROADCASTING ALONG WITH THE FLOOR

 

 

 

WALL SEPARATELY DUE TO FLAKE SIZE CHANGE  

 

 

 

 

As you can imagine after looking at the videos, I'm sure you can realize the potential to put

more money in your pocket on every broadcast project going forward.

 

IF YOU SAW ALL THE ICONS OF OUR CLIENTS NEXT TO 'WHAT PROFESSIONAL APPLICATORS SAY' ON THE HOME PAGE, THAT'S JUST A HANDFUL FROM AROUND THE WORLD THAT USE OUR SYSTEM, AND THE LIST GROWS EVERYDAY. 

IT'S REALLY A NO BRAINER! 

What are you waiting for?  

Just click on this 'PRODUCT' to start saving big MONEY.